,
|
|
|
Controls |
| Request Controls Quote |
| Click here to request a controls quote online. |
| Micro Controllers |
|
|
|
Magnum with OEM mounted Keypad / LCD assembly |
|
|
|
Magnum with Panel mounted Keypad / LCD assembly |
|
|
|
Magnum with Door mounted Keypad / LCD assembly |
|
|
|
Magnum (Board only) |
|
Options available for the MCS-MAGNUM micro controller. Add these extensions to the end of the part number for a MCS-MAGNUM assembly listed above. |
|
-24 |
24vac input power |
|
MCS-MAGNUM Control Cabinets Master micro controller board with twelve 0-5vdc sensor inputs, four 5vdc digital inputs, ten 230vac 6.3amp relay outputs, four 0-10vdc analog outputs, keypad, 128 x 64 dot pixel STN monochrome graphics LCD with 2.8" diagonal viewing area, real time clock, MCS-I/O, RS-232, RS-485 and Ethernet communication ports. User selectable 115vac or 230vac operation. |
| MCS-MAGNUM-SB | MCS-MAGNUM in Box Enclosure 16"w x 18"h x 6"d |
|
| MCS-MAGNUM-MB | MCS-MAGNUM in Box Enclosure 20"w x 24"h x 6"d | |
| MCS-MAGNUM-LB | MCS-MAGNUM in Box Enclosure 32"w x 27"h x 6"d |
|
| MCS-MAGNUM-SB-NEMA | MCS-MAGNUM in NEMA 4 Enclosure 20"w x 24"h x 6"d |
|
| MCS-MAGNUM-MB-NEMA | MCS-MAGNUM in NEMA 4 Enclosure with swing panel 24"w x 30"h x 12"d |
|
Options available for all the MCS-MAGNUM Control Cabinets listed above. Factory installed at MCS. When ordering, please list these as separate part numbers. |
|
-MB-MAGNUM-24 |
24vac power input option |
|
|
-MB-WARNING-(24/115/230) |
Yellow warning indicator |
|
|
-MB-ALARM-(24/115/230) |
Red alarm indicator |
|
|
-MB-RUN-LT#(1/2/3/4) |
Green run indicator |
|
|
-MB-RUN-SW |
Run/Stop selector switch |
|
|
-MB-EMERG-SW |
Emergency Stop switch |
|
|
-MB-COMP#(1/2/3/4) |
Single compressor on/off switch |
|
|
-MB-BYPASS |
Momentary bypass push button |
|
| Modem 115vac |
|
|
| Modem 230vac | ||
|
-MB-24VOLT-(115/230) |
115(230) to 24vac transformer |
|
Options available only for the MCS-MAGNUM-MB, -MB-NEMA and -LB Control Cabinets listed above. Factory installed at MCS. When ordering, please list these as separate part numbers. |
| MCS-RO10 relay output expansion board |
|
|
| MCS-SI16-AO4 sensor input and analog output expansion board |
|
|
| MCS-I/O-N expansion board |
|
|
|
-MB-SE-IB1 |
Control board for 20 ton EXV, 24vac power required |
|
|
-MB-SE-IB3 |
Control board for 30 ton EXV, 24vac power required |
|
|
-MB-SE-IB6 |
Control board for 50+ ton EXV, 24vac power required | |
|
-MB-24VOLT-(115/230) |
115(230) to 24vac transformer |
|
Options available only for the MCS-MAGNUM-LB Control Cabinets listed above. Factory installed at MCS. When ordering, please list these as separate part numbers. |
|
-LB-MAG-TOUCH-8C |
MCS-MAG-TOUCH-8C in Box Enclosure 32"w x 27"h x6"d. For indoors use only. |
|
MCS-8 Master micro controller board with eight 0-5vdc sensor inputs, eight 115vac 10amp relay outputs, one 0-10vdc / 4-20ma analog output, keypad, 16 character x 2 line large character backlit display, real time clock, MCS-I/O, RS-232 and RS-485 communication ports. |
| MCS-8-B-BLCD | MCS-8 in Box Enclosure |
|
| MCS-8-B-REMOTE | MCS-8 in Box Enclosure for Remote Keypad Access |
|
| MCS-8-D-BLCD | MCS-8 Door Panel Package |
|
| MCS-8-P-BLCD | MCS-8 Inside Control Panel Mounting Package |
|
| MCS-8-N | MCS-8 (Board only) |
|
Options available for the MCS-8 micro controller. Add these extensions to the end of the part number for a MCS-8 assembly listed above. |
|
-24 |
24vac input power |
|
|
-230 |
230vac input power |
|
MCS-6 A stand-alone unitary micro controller with eight 0-5vdc sensor inputs, six 24vac 5amp relay outputs with LED status indicators, one 0-10vdc analog output, two RS-485 communication ports, eight alarm LEDs, no keypad or display. Board mounts with four #6 sheet metal screws and comes with a Lexan cover. |
| MCS-6 | MCS-6 (Board only) |
|
Software Options available for the MCS-6. Add these extensions to the end of the part number for a MCS-6 assembly listed above. |
|
-CND |
Software for the efficient control of condenser fans | |
|
-HCU |
Software for humidity control units for dehumidification |
|
| Software for controlling heat pumps |
|
| Expansion Boards |
MCS-RO10 Expansion board for a MCS-MAGNUM or MCS-8 with ten 230vac 6.3amp relay outputs, MCS-I/O communication port, no keypad or display. Suitable replacement for MCS-RO8 board. User selectable 115vac or 230vac operation. |
|
MCS-RO10 (Board only), mounts with four #6 sheet metal screws and comes with a Lexan cover |
|
Options available for the MCS-RO10 expansion board. Add these extensions to the end of the part number for an MCS-RO10 assembly listed above. |
|
-24 |
24vac input power |
|
MCS-I/O Expansion board for a MCS-MAGNUM or MCS-8 with eight 0-5vdc sensor inputs, eight 115vac 10amp relay outputs, one 0-10vdc / 4-20ma analog output, MCS-I/O and RS-485 communication ports, no keypad or display. |
| MCS-I/O-B | MCS-I/O in Box Enclosure |
|
| MCS-I/O-P | MCS-I/O Inside Control Panel Mounting Package |
|
| MCS-I/O-N | MCS-I/O (Board only) |
|
Options available for the MCS-I/O expansion board. Add these extensions to the end of the part number for a MCS-I/O assembly listed above. |
|
-24 |
24vac input power |
|
|
-230 |
230vac input power |
|
| Demonstration Units |
|
|
|
Door Mount |
|
MAGNUM-DEMOCASE MAGNUM micro controller board with twelve 0-5vdc sensor inputs, four 5vdc digital inputs, ten 230vac 6.3amp relay outputs, four 0-10vdc analog outputs, keypad, 128 x 64 dot pixel STN monochrome graphics LCD with 2.8" diagonal viewing area, real time clock, MCS-I/O, RS-232, RS-485 and Ethernet communication ports. Mounted inside a rugged aluminum briefcase and incorporating indicator lights, switches and variable potentiometers that allows the user to easily simulate a wide variety of conditions and visually see what is happening as if it was controlling an actual unit. User selectable 115 or 230vac operation. |
| MAGNUM-DEMOCASE | Briefcase |
|
MCS-8-DEMO MCS-8 master micro controller with eight potentiometer-controlled 0-5vdc sensor inputs, eight 115vac 10amp relay outputs with LED status lights, one 0-10vdc / 4-20ma analog output, keypad, 16 character x 2 line large character backlit display, real time clock, MCS-I/O, RS-232 and RS-485 communication ports. Includes cable (specify MCS-PC25 or MCS-PC9) for MCS-8 to PC communication. User selectable 115vac or 230vac operation. |
| MCS-8-DEMO | Panel Mount |
|
MCS-I/O-DEMO MCS-I/O slave micro controller expansion board with eight potentiometer-controlled 0-5vdc sensor inputs, eight 115vac 10amp relay outputs with LED status lights, one 0-10vdc / 4-20ma analog output, MCS-I/O and RS-485 communication ports. User selectable 115 or 230vac operation. |
|
MCS-I/O-DEMO |
Panel Mount |
|
MCS-6-DEMO Unitary stand-alone MCS-6 micro controller with socketed microprocessor, eight potentiometer-controlled 0-5vdc sensor inputs, six 24vac 5amp relay outputs with LED status indicators, one 0-10vdc analog output, two RS-485 communication ports, eight alarm LEDs, no keypad or display. Also includes an MCS-STAT-HUMD, MCS-485-GATEWAY and cable (specify MCS-PC25 or MCS-PC9) for PC communications. |
|
MCS-6-DEMO |
Panel Mount |
|
| Peripherals |
| FLASH-1GB | 1GB compact flash memory card | |
| MCS-COMPACT | Adapter board for compact flash socket | |
|
Communications bridge between the signal levels and protocols of RS-485 and RS-232. Supports baud rate of 19.2Kb/sec as standard. |
|
|
| MCS-485-GWY9600 | Communications bridge between the signal levels and protocols of RS-485 and RS-232. Supports baud rate of 9.6Kb/sec as standard. |
|
|
MCS-AOHC |
Analog Output High Current board. Accepts 0-10vdc input from the analog output of a MCS micro controller and 12vdc from a high current source to output up to 5 amps based on analog input voltage. |
|
| MCS-ETHERNET | RS-232 to Ethernet device server with 100-240vac power adapter. Used to allow PC-Connect and MCS-Connect to communicate with MCS micro controllers over Ethernet. |
|
| MCS-ETHERNET-SWITCH | 5-port 10/100Base-TX Ethernet switch with power supply. |
|
|
MCS-FREQ |
Frequency to Voltage conversion board. Accepts HOOF 9104 Magnetic Pickup Sensor. |
|
| MCS-LGE | BACnet router module that provides communication between an Ethernet or IP network and a MCS-UPC or MCS-PORTAL | |
| MCS-MAGTOUCH-8C | 8" TFT Color touch screen for MCS-MAGNUM's. For indoor use only. | |
| MCS-MAGTOUCH-PR | One-time fee for programming a MCS-MAGTOUCH-8C for five screens. | |
| MCS-MAGTOUCH-485-ADAPTER | Adapter for RS-485 network communications. | |
| MCS-ROUTER | 5-port Wireless-G router programmed for port forwarding that allows connection of up to four MCS-MAGNUM's using only one static IP address. Mounted in plastic box. Must fill out the MCS-ROUTER Program Request Form. | |
| MCS-SI-SELECTOR | Routes the greater of two sensor input voltages to one output. | |
|
Solid state relay board used in conjunction with an MCS-RO8-SSM for high cycle relay operation. Features a single solid state relay with a normally open output that closes with an input of 3-32vdc. It can switch output loads of up to 2A at 280vac. |
|
|
|
Communicating thermostat with large character LCD that shows actual room temperature along with cooling and heating setpoints that can be changed directly from the thermostat. System and Fan control switches, along with an override pushbutton are also provided. Designed to connect to a MCS micro controller. |
|
|
|
Communicating thermostat with large character LCD that shows actual room temperature and humidity along with cooling and heating setpoints that can be changed directly from the thermostat. System and Fan control switches, along with an override pushbutton are also provided. Designed to connect to a MCS micro controller. |
|
|
| MCS-USB-RS232 | USB to Serial DB9 male converter | |
|
MCS-WHTR-BOX |
Printed circuit board that contains relays and terminal strips to interrupt the 240vac power line to a hot water heater. Terminal strips allow the user to easily connect a MCS-T100 temperature sensor and control wiring to a MCS micro controller. |
|
| MODEM | External modem pre-programmed for use with MCS micro controllers (includes MCS-M9-M25 cable, RJ-11 phone cable and 120vac to 7.5vdc AC Adapter with surge suppressor) | |
| MODEM-230 | External modem pre-programmed for use with MCS micro controllers (includes MCS-M9-M25 cable, RJ-11 phone cable and 90-264vac to 7.5vdc AC Adapter) | |
| MODEM-MAG-115 | External modem pre-programmed for use with MCS-MAGNUM micro controllers (includes MCS-485-GATEWAY, MCS-M9-M25 cable, RJ-11 phone cable and 120vac to 7.5vdc AC Adapter with surge suppressor) |
|
|
External modem pre-programmed for use with MCS-MAGNUM micro controllers (includes MCS-485-GATEWAY, MCS-M9-M25 cable, RJ-11 phone cable and 90-264vac to 7.5vdc AC Adapter) |
|
| Portals | |||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||
| Sensors | |||||||||||||||||||||||||||||||||||||
|
300:0.2 current transformer with circuitry to convert induced ac voltage into a 0-5vdc output voltage. Wire hole diameter: 1.00" |
|
|
| MCS-CT500 | 500:0.2 current transformer with circuitry to convert induced ac voltage into a 0-5vdc output voltage. Wire hole diameter: 1.56" |
|
|
1500:0.2 current transformer with circuitry to convert induced ac voltage into a 0-5vdc output voltage. Wire hole diameter: 4.50" |
|
|
|
MCS-FLOW-SW |
Differential pressure switch with working range of 3-150 psi and adjustment range of 3-40 psi. Contacts rated at maximum of 4 amps at 250vac. |
|
|
MCS-H100 |
MCS-HUMD (Board only) |
|
|
Combination humidity and temperature sensor board packaged in a plastic housing 2.00"w x 2.57"l x 1.50"h |
|
|
|
MCS-HUMD with override pushbutton |
|
|
| MCS-PHASE | Three phase voltage monitor / 190-630vac 50-60Hz |
|
|
A MCS-T100 temperature sensor with an air supply bracket. Mounting base is 2" x 2" and requires a minimum of 2.25" for inserting into air duct. Comes with 20' of 2 conductor shielded cable. |
|
|
|
A MCS-T100 temperature sensor with an air supply bracket. Mounting base is 2" x 2" and requires a minimum of 2.25" for inserting into air duct. Comes with 40' of 2 conductor shielded cable. |
|
|
| MCS-SAIR-60 | A MCS-T100 temperature sensor with an air supply bracket. Mounting base is 2" x 2" and requires a minimum of 2.25" for inserting into air duct. Comes with 60' of 2 conductor shielded cable. |
|
|
Differential pressure transducer designed to be used with air or nonconducting gases. Range: 0-5.0" WC |
|
|
| MCS-STATIC-50" | Differential pressure transducer designed to be used with air or nonconducting gases. Range: 0-50.0" WC |
|
|
-40° to +270°F (-40° to +132°C) temperature sensor in a stainless steel deep drawn tube with 20' of 2 conductor shielded cable. |
|
|
|
-40° to +270°F (-40° to +132°C) temperature sensor in a stainless steel deep drawn tube with 40' of 2 conductor shielded cable. |
| MCS-T100-60 | -40° to +270°F (-40° to +132°C) temperature sensor in a stainless steel deep drawn tube with 60' of 2 conductor shielded cable. |
|
| MCS-T100-L-20 | -60° to +48°F (-51° to +9°C) temperature sensor in a stainless steel deep drawn tube with 20' of 2 conductor shielded cable. |
|
| MCS-T100-L-40 | -60° to +48°F (-51° to +9°C) temperature sensor in a stainless steel deep drawn tube with 40' of 2 conductor shielded cable. |
|
| MCS-T300 | -22° to +125°F (-30° to +51.6°C) temperature sensor in nickel plated copper deep drawn tube with 60' of 3 conductor shielded cable. | |
| MCS-T300L | -76° to +32°F (-60° to 0°C) temperature sensor in nickel plated copper deep drawn tube with 60' of 3 conductor shielded cable. | |
| MCS-T300H | 32° to +250°F (0° to +121.1°C) temperature sensor in nickel plated copper deep drawn tube with 60' of 3 conductor shielded cable. | |
| MCS-T-CONV | Converts an MCS-T100 2 wire to 3 wire mode |
|
|
Thin walled deep drawn copper tube 2¾" long with an 0.425" outside diameter filled with heat transfer grease. Designed to hold a MCS-T100 temperature sensor. |
|
|
| MCS-WELL-1/4 | A tube filled with heat transfer grease that has been soldered onto a ¼" brass hex fitting with NPT tread. Total length is 2½" |
|
|
A tube filled with heat transfer grease that has been soldered onto a ½" brass hex fitting with NPT tread. Total length is 2¾" |
|
|
|
A MCS-TUBE filled with heat transfer grease that has been soldered onto a ¾" brass hex fitting with NPT tread. Total length is 2¾" |
|
|
| MCS-Z100 | Replacement MCS-T100 temperature sensor for MCS-ZONE |
|
| MCS-ZONE | Temperature sensor board packaged in a plastic housing 2.00"w x 2.57"l x 1.50"h |
|
| MCS-ZONE-OVR | MCS-ZONE with an override pushbutton. |
|
| PACK-CON-20 | Packard connector with 20' 3 wire shielded cable for MCS pressure transducers. |
|
| PACK-CON-40 | Packard connector with 40' 3 wire shielded cable for MCS pressure transducers. |
|
|
PACK-CON-60 |
Packard connector with 60' 3 wire shielded cable for MCS pressure transducers. |
|
| TI-150A | 0 to 150 psi absolute pressure transducer with ¼" SAE female flare fitting and deflator. (Sensor only) |
|
| TI-150A-20 | 0 to 150 psi absolute pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 20' of 3 wire shielded cable. |
|
| TI-150A-40 | 0 to 150 psi absolute pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 40' of 3 wire shielded cable. |
|
| TI-150A-60 | 0 to 150 psi absolute pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 60' of 3 wire shielded cable. |
|
| TI-200F | 0 to 200 psi gage pressure transducer with ¼" SAE female flare fitting and deflator. (Sensor only) |
|
| TI-200F-20 | 0 to 200 psi gage pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 20' of 3 wire shielded cable. |
|
|
0 to 200 psi gage pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 40' of 3 wire shielded cable. |
|
|
| TI-200F-60 | 0 to 200 psi gage pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 60' of 3 wire shielded cable. |
|
| TI-500-AMM | 0 to 500 psi gage pressure transducer for ammonia applications. Internal components are packaged in a stainless steel housing with a ⅛"-27 NPT-2A male fitting. (Sensor only) |
|
| TI-500-AMM-20 | 0 to 500 psi gage pressure transducer for ammonia applications. Internal components are packaged in a stainless steel housing with a ⅛"-27 NPT-2A male fitting. Supplied with a packard connector and 20' of 3 wire shielded cable. |
|
| TI-500-AMM-40 | 0 to 500 psi gage pressure transducer for ammonia applications. Internal components are packaged in a stainless steel housing with a ⅛"-27 NPT-2A male fitting. Supplied with a packard connector and 40' of 3 wire shielded cable. |
|
| TI-500-AMM-60 | 0 to 500 psi gage pressure transducer for ammonia applications. Internal components are packaged in a stainless steel housing with a ⅛"-27 NPT-2A male fitting. Supplied with a packard connector and 60' of 3 wire shielded cable. |
|
| TI-500F | 0 to 500 psi gage pressure transducer with ¼" SAE female flare fitting and deflator. (Sensor only) |
|
|
0 to 500 psi gage pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 20' of 3 wire shielded cable. |
|
|
|
0 to 500 psi gage pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 40' of 3 wire shielded cable. |
|
|
| TI-500F-60 | 0 to 500 psi gage pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 60' of 3 wire shielded cable. |
|
| TI-667A | 0 to 667 psi absolute pressure transducer with ¼" SAE female flare fitting and deflator. (Sensor only) |
|
| TI-667A-20 | 0 to 667 psi absolute pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 20' of 3 wire shielded cable. |
|
| TI-667A-40 | 0 to 667 psi absolute pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 40' of 3 wire shielded cable. |
|
|
0 to 667 psi absolute pressure transducer with ¼" SAE female flare fitting and deflator. Supplied with a packard connector and 60' of 3 wire shielded cable. |
|
| Electronic Expansion Valves |
| MCS-SE-IB1 | Temperature control board for Sporlan SEI-20 Expansion Valves. 24vac required. | |
|
MCS-SE-IB3 |
Temperature control board for Sporlan SEI-30 Expansion Valves. 24vac required. |
|
|
MCS-SE-IB6 |
Temperature control board for Sporlan SEI-50, SEH-100 and SEH-175 Expansion Valves. 24vac required. |
|
| MCS-SER-20 | 20 Ton Sporlan Expansion Valve 5/8" inlet fitting, 1-1/8" outlet fitting with 30' cable |
|
|
MCS-SEI-30 |
30 Ton Sporlan Expansion Valve |
|
| MCS-SEI-50 | 50 Ton Sporlan Expansion
Valve 1-1/8" inlet fitting, 1-5/8" outlet fitting with 30' cable |
|
| MCS-SEI-100 | 100 Ton Sporlan Expansion
Valve 1-3/8" inlet fitting, 1-5/8" outlet fitting with 30' cable |
|
|
MCS-SEI-175 |
175 Ton Sporlan Expansion Valve |
|
| Support Services |
| CFG-DEV | Development of a new config model |
|
| DRAWINGS | Wiring Diagrams for MCS micro controllers | |
| HHSERV | Hourly service rate (Not including travel expenses) |
|
| SW-DEV | Software development (Not including travel expenses) |
|
| PC Software |
|
MCS- CFG |
A Microsoft Windows® program that builds the Config file that contains model information for a given application. This is a site license and includes a printed manual. |
|
| MCS-CONNECT | A Microsoft Windows® program that communicates with MCS-8 and MCS-MAGNUM micro controllers. Communications can be either local or remote via a modem. This is a site license and includes a printed manual. | |
|
A Microsoft Windows® program that communicates with MCS-8 and MCS-6 micro controllers. Communications can be either local or remote via a modem. This is a site license and includes a printed manual. |
|
| MCS-8 Software |
|
CFG-CHIP |
2864 8K EEROM programmed with a user specified configuration file. |
|
|
GAL |
GAL22V10-25ns programmed for MCS-8 and MCS-I/O hardware revisions 1.3 or higher (specify revision level and control software being used when ordering.) |
|
| SW-CHIP | 27C512 64K EPROM programmed with MCS-8 control software (Specify application control software such as chiller screw, reciprocating, etc.) Note: This may require the GAL chip to be upgraded depending on the software revision. Contact MCS for details. |
| Miscellaneous Items |
|
25-000 |
315ma 120 volt 5 x 20mm glass tube fuse |
|
|
25-004 |
10amp 120volt 5 x 20mm glass tube fuse |
|
|
25-005 |
2amp 120 volt 5 x 20mm glass tube fuse |
|
| 25-007 | 1amp 120 volt 5 x 20mm glass tube fuse |
|
| 25-008 | 5amp 120 volt 5 x 20mm glass tube fuse |
|
| 25-010 | 500ma 120 volt 5 x 20mm glass tube fuse |
|
| 25-024 | 5amp mini auto fuse |
|
| 32-004 | 65176 (RS-485) chip |
|
| 32-006 | RS-232 chip |
|
|
33-000 |
Blank 27C512 64K EPROM |
|
|
33-002 |
Blank 2864 8K EEROM |
|
|
40-022 |
Mini Berg Jumper (2 position jumper) |
|
|
41-000 |
RIA 3 position terminal header (top part with screw terminals for sensor input, analog out, etc. bases.) |
|
|
41-006 |
AUGAT 6DTB 3 position terminal header (top part with screw terminals for relay output and power input connector bases.) |
|
| 41-007 | MAGNUM 3 position terminal header (top part with screw terminals for relay output and power input connector bases. With protective flip top cover.) |
|
| 41-036-3 | MAGNUM 3 position vertical terminal header (top part wih screw terminals for relay output and power input connector bases. | |
| 41-038-3 | Tyco 3 position 5mm terminal header (top part with screw terminals for sensor input, analog output, etc. bases) | |
|
91-294 |
4/40 Nylon acorn nut |
|
|
LCD-BL-KIT |
Backlit LCD assembly with mounting hardware |
|
|
MCS-100 OHM |
100-ohm resistor for use with dry contact on sensor inputs. |
|
| MCS-24-VOLT-115 | 115 to 24vac transformer | |
| MCS-24-VOLT-230 | 230 to 24vac transformer | |
| MCS-EPOXY | Steel reinforced epoxy putty stick | |
|
MCS-M25 |
MCS 9 pin (male) to Modem 25 pin (male) |
|
| MCS-M25 | MCS 9 pin (male) to Modem 25 pin (male) |
|
|
MCS-MANUAL
|
Although printed manuals may be ordered from MCS for a fee, a selection of manuals may be downloaded free of charge from our Literature page. |
|
|
MCS-PC25 |
MCS 9 pin (male) to PC 25 pin (male) |
|
|
MCS-PC9 |
MCS 9 pin (male) to PC 9 pin (female) |
|
| MCS-RS232-EXT | Extension cable for the RS-232 port. 9-pin male to 9-pin female. | |
| MCS-SNUBBER | External snubber suppression network | |
| RS-485 PROTECT | Surge protector for RS-485 communication lines |
|
|
|