|
|
| Literature |
| Application Notes |
| APP-061 | Hanbell Jumper Bar Installation | |
| APP-060 | Downloading a CFG file into a MCS-LONTALK-OEM | |
| APP-059 | Installing a MCS-T100 Temperature Sensor | |
| APP-058 | MCS-MAGNUM Interface to Copeland Digital Scroll | |
| APP-057 | Setting Up an Internet Connection for the MCS-MAGNUM | |
| APP-056 | MCS-RO8 to MCS-RO10 Migration | |
| APP-055 | Mounting the latest MCS-Keypad | |
| APP-054 | Replacing a MCS-RO8 board with an MCS-RO10 | |
| APP-053 | MCS-Bleed Installation | |
| APP-052 | Carrier 5K Temperature Sensors | |
| APP-051 | Hanbell Screw (with Step Slide) Applied to McQuay Micro Tech II Controllers | |
| APP-050 | Hanbell Oil Level Switch Installation RC12~RC18, RC2-170, RC2-200~580, RC2-620 |
|
| APP-049 | Setting the Brownout Point for a MCS-MAGNUM | |
| APP-047 | MCS-IB-CAP Installation | |
| APP-046 | MCS-T300, MCS-T300HT, and MCS-T300LT Temperature Sensor Input to MCS-MAGNUM | |
| APP-045 | Hanbell Step Capacity Loading | |
| APP-044 | Hanbell PT1000 Temperature Sensor Input to MAGNUM | |
| APP-043 | 230vac Control Power and Snubber Networks | |
| APP-042 | 2007 Daylight Saving Time Change And the MCS-8 | |
| APP-041 | Hanbell Procedure to Change SV Stepless to Step with Mounting Type Normally Open SV Notes | |
| APP-040 | Hanbell Oil Float Dampers Shield Notes | |
| APP-039 | Heat Pump V9 Software Notes | |
| APP-038 | Improving Noise Immunity in MCS-8 Optrex LCD Displays | |
| APP-037 | Using a Lantronix UDS-10 to Allow PC-Connect to Communicate Over a LAN | |
| APP-036 | Understanding PPTC Devices And Their Use In Protecting MCS Products | |
| APP-035 | Modifying Selected MCS Products For Use With Another Operating Voltage | |
| APP-034 | Software ACDRB Refrigeration Control New Defrost Feature | |
| APP-033 | MCS-6 HCU Digital Wireless Modem Support | |
| APP-032 | Troubleshooting Loss of Vaa On MCS-8 & MCS-I/O Boards | |
| APP-031 | Demo Reciprocating/Screw Panel Panel Swap Instruction Sheet | |
| APP-030 | Napps Eng Transducer Options | |
| APP-029 | MCS-8 & MCS-I/O Modifications to make Rev 1.565 |
|
| APP-028 | A/D SCR Latch Up | |
| APP-027 | Snubber Capacitor Testing | |
| APP-026 | MCS-I/O Network Setup | |
| APP-025 | Removal of the 1N5817 Diodes | |
| APP-024 | Hartford Screw Compressor | |
| APP-023 | EEPROM Write Enable Jumper | |
| APP-022 | Installation of LCD Insulator | |
| APP-021 | PC CONN print to a file | |
| APP-020 | Dunham-Bush 2 Pump Control ACDRB 07.30-A EXV 07.30-A | |
| APP-019 | MCS-8 Keypad Functions | |
| APP-018 | FHP's MCS-8 Target Reset | |
| APP-017 | Chilled Water Reset CHLR05.00-c & -u Screw Control | |
| APP-016 | Hot Gas Bypass (HGB) CHLS05.00-c & -u Screw Control | |
| APP-015 | Variable Speed Condenser Fan Logic | |
| APP-014 | MCS-8 Chiller Software Version CHL S05.00-O | |
| APP-013-B | Removal of Ferrite Bead on MCS-8, MCS-I/O, SI8, SI16 & RO8 Boards | |
| APP-013-A | Removal of Two Ferrite Beads on MCS-8 and MCS-I/O Rev 1.50 Boards | |
| APP-013 | MCS-8 & MCS-I/O Hardware Revision 1.5 Update | |
| APP-012 | Six Board Class Definitions | |
| APP-011 | Four Board Class Definitions | |
| APP-010 | Connecting the MCS-8 to a Building Management System | |
| APP-009 | Hall Screw Compressors | |
| APP-008 | Hitachi Screw Point List and Startup Sequence | |
| APP-007 | MCS-8 RS232 & RS485 Network Protocol | |
| APP-006 | Home Load Manager Installation Manual Hardware Revision 1.4 & Higher |
|
| APP-005 | OEM Installation Hardware Revision 1.4 & Higher |
|
| APP-004 | RS485 Network Installation | |
| APP-003 | Installation of Software and Config Chips | |
| APP-002 | Installation of Snubber Capacitors | |
| APP-001 | Relay Output Sequence for Heatcraft Chillers |